Difference between revisions of "Board:asus/p5gc-mx"

From coreboot
Jump to: navigation, search
(P5GC-MX: Add initial info)
 
m (P5GC-MX S3)
Line 75: Line 75:
 
|Reboot_status = OK
 
|Reboot_status = OK
 
|Poweroff_status = OK
 
|Poweroff_status = OK
|Suspend_status = No
+
|Suspend_status = OK
 +
|Suspend_comments = [https://review.coreboot.org/#/c/19602/ WIP] BSEL straps are at 800MHz FSB on resume. Some CPUs don't like this
 
|LEDs_status = OK
 
|LEDs_status = OK
 
|HPET_status = Unkown
 
|HPET_status = Unkown

Revision as of 18:53, 12 May 2017

This page describes how to use coreboot on the Asus P5GC-MX mainboard.


Status (as of commit 0117924159)

Device/functionality Status Comments
CPU
CPU works OK Core 2 duo up to 1067MHz FSB. Pentium 4-like CPUs don't boot.
L1 cache enabled OK
L2 cache enabled OK
L3 cache enabled N/A
Multiple CPU support N/A
Multi-core support OK Quad cores are not supported by the chipset
Hardware virtualization Untested
RAM
EDO N/A
SDRAM N/A
SO-DIMM N/A
DDR N/A
DDR2 OK
DDR3 N/A
Dual channel support N/A
ECC support N/A
On-board Hardware
On-board IDE 3.5" Untested
On-board IDE 2.5" Untested
On-board SATA OK
On-board SCSI N/A
On-board USB OK
On-board VGA OK VBIOS works. Only textmode available for native graphic init
On-board Ethernet OK
On-board Audio OK
On-board Modem N/A
On-board FireWire N/A
On-board Smartcard reader N/A
On-board CompactFlash N/A
On-board PCMCIA N/A
On-board Wifi N/A
On-board Bluetooth N/A
On-board SD card reader N/A
Add-on slots/cards
ISA add-on cards N/A
Audio/Modem-Riser (AMR/CNR) cards N/A
PCI add-on cards OK
Mini-PCI add-on cards N/A
Mini-PCI-Express add-on cards Unknown
PCI-X add-on cards N/A
AGP graphics cards N/A
PCI Express x1 add-on cards N/A
PCI Express x2 add-on cards N/A
PCI Express x4 add-on cards N/A
PCI Express x8 add-on cards N/A
PCI Express x16 add-on cards Has problems SDVO/ADD2 cards work fine. External GPUs easily hang the system.
PCI Express x32 add-on cards N/A
HTX add-on cards N/A
Legacy / Super I/O
Floppy Untested
Serial port 1 (COM1) OK
Serial port 2 (COM2) Untested
Parallel port Untested
PS/2 keyboard OK
PS/2 mouse Untested
Game port N/A
Infrared N/A
PC speaker N/A
DiskOnChip N/A
Input
Trackpoint N/A
Touchpad N/A
Fn Hotkeys N/A
Fingerprint Reader N/A
Laptop
Docking VGA N/A
Docking LAN N/A
Docking USB N/A
Docking Audio N/A
Docking Displayport N/A
Thinklight N/A
Webcam N/A
Miscellaneous
Sensors / fan control OK
Hardware watchdog Unknown
SMBus OK
CAN bus N/A
CPU frequency scaling OK
Other powersaving features Unknown
ACPI OK
Reboot OK
Poweroff OK
Suspend OK WIP BSEL straps are at 800MHz FSB on resume. Some CPUs don't like this
Nonstandard LEDs OK
High precision event timers (HPET) Unkown
Random number generator (RNG) N/A
Wake on modem ring Unknown
Wake on LAN Unknown
Wake on keyboard Unknown
Wake on mouse Unknown
TPM Unknown
Flashrom OK Can be flashed from vendor bios. Has a DIP8 socket.

Peculiarities

Normally on boards with an LGA755 socket the FSB multiplier is determined by 3 pins/straps on the CPU called BSEL. On this board those pins on the CPU are not hooked up to the memory controller, but some GPIOs on the SuperIO are used instead. The result is that to set up the correct FSB the SuperIO needs to be configured and then the system reset. Since this reset takes a few seconds, the fans will spin up, than spin down again to resume a full boot a few seconds later.

Variants

  • The P5GC-MX/1333 might work just fine with the current code. The P5GC-MX/1333 vendor bios works fine on P5GC-MX but does not configure the SuperIO GPIO BSEL straps correctly which might indicate that it does not have those.
  • P5GC-MX/GBL ?