The wiki is being retired!
Documentation is now handled by the same processes we use for code: Add something to the Documentation/ directory in the coreboot repo, and it will be rendered to https://doc.coreboot.org/. Contributions welcome!
Before you begin
The Gigabyte M57SLI-S4 seems to exist in at least 2 versions: one with a PLCC socket for the BIOS chip (socketed BIOS), and one with the PLCC BIOS chip soldered onto the board (soldered BIOS). The former might be a pre-production board since nobody has so far (2007/03) confirmed the purchase of a M57SLI-S4 board with socketed BIOS.
The fact that the BIOS is soldered onto the board complicates matters considerably, because it means that one flash of a faulty image will 'brick' your board.
It is possible to desolder the BIOS chip, and replace it with a PLCC socket. You will need some tools (heat gun/pencil, good soldering iron, etc) and soldering experience to do that. The other option is to add a PLCC socket to the empty position next to the soldered-on BIOS chip. With an extra resistor and a switch, this allows switching between 2 BIOS chips. This has been documented carefully by ST; see his instructions.
If you're going to work on this board, you need a backup plan in the event you flash a faulty BIOS image (it's called 'bricking' the board). I suggest you put a socket on it, or ask a friend to do so. It's just too risky otherwise.
Once you put a socket on the board, you will also discover that the RD1-PMC4 BiosSavior does not work with this motherboard: the RD1's built-in chip seems to be incompatible with the mainboard. This means you will need to hot-swap BIOS chips until you have a working LinuxBIOS chip. Plugging your BIOS chip into the RD1 and switching it to 'ORG' does work though. I have used the BiosSavior to ease hot swapping; it's a lot easier to pull out the BiosSavior and replace the chip plugged into it than to replace the ROM chip on the board.
This is the list of BiosSavior resellers:
In the US, FrozenCPU seems to have stock (verified 2007/04). Eksitdata in Sweden also seems to have stock (verified 2007/03).
This wiki page is maintained by Ward Vandewege (ward at gnu dot org).
LinuxBIOS requires a Payload to boot an operating system.
If you want to boot from the network, you will need to use Etherboot.
If you want to boot from an IDE drive, SATA drive, USB stick or CDROM, you can use FILO.
Building the payload
In order to boot from a SATA disk, we use FILO.
Once you've downloaded FILO, you will need to put a file 'Config' in its root tree. An example can be found in the distribution, called 'defconfig'.
You can configure FILO to load Grub. Here's my Config, which does that:
# Use grub instead of autoboot? USE_GRUB = 1 # Grub menu.lst path MENULST_FILE = "hde1:/grub/menu.lst" # Driver for hard disk, CompactFlash, and CD-ROM on IDE bus IDE_DISK = 1 # Add a short delay when polling status registers # (required on some broken SATA controllers) IDE_DISK_POLL_DELAY = 1 # Driver for USB Storage USB_DISK = 1 # VGA text console VGA_CONSOLE = 1 PC_KEYBOARD = 1 # Enable the serial console SERIAL_CONSOLE = 1 # Serial console; real external serial port SERIAL_IOBASE = 0x3f8 SERIAL_SPEED = 115200 # Filesystems FSYS_EXT2FS = 1 FSYS_ISO9660 = 1 # Support for boot disk image in bootable CD-ROM (El Torito) ELTORITO = 1 # PCI support SUPPORT_PCI = 1 # Enable this to scan PCI busses above bus 0 # AMD64 based boards do need this. PCI_BRUTE_SCAN = 1 # Loader for standard Linux kernel image, a.k.a. /vmlinuz LINUX_LOADER = 1
Because physical disks take a while to spin up, I've had to add an extra delay to FILO:
Index: main/filo.c =================================================================== --- main/filo.c (revision 34) +++ main/filo.c (working copy) @@ -60,6 +60,7 @@ /* Initialize */ init(); + delay (5); grub_main(); return 0; }
This will make FILO wait 5 seconds before probing the disks, making sure that the SATA disk is ready.
In order to get serial output from Grub, you will also need to add something like this to your menu.list:
# serial port 0 serial --unit=0 --speed=115200 terminal --timeout=15 serial console
Now execute 'make', which will generate a filo.elf file that will be your payload. You will need to refer to this file to build LinuxBIOS as explained below, because it gets included in the LinuxBIOS ROM image.
When using FILO in grub emulation mode, it's important to get a few details right in your grub boot stanza. This is what mine looks like:
title Ubuntu LB, kernel 2.6.21-rc3 root (hd4,0) kernel /boot/vmlinuz-2.6.21-rc3 root=/dev/sda1 ro acpi_use_timer_override console=tty0 console=ttyS0,115200 savedefault boot
Note the root device - FILO sees the first sata device as hd4.
Also, the m57sli-s4 will not boot unless you add acpi_use_timer_override as a kernel option - and use a modern kernel (tested on 188.8.131.52 and up). Hopefully this will be fixed in newer kernels. If you have a somewhat older kernel (tested with 2.6.16 and up), add these options: apic=debug acpi_dbg_level=0xffffffff pci=noacpi,routeirq snd-hda-intel.enable_msi=1.
Current status of the LBv2 tree
Use revision 2619 or higher.
Make sure that the path to your payload is correct, by editing
and updating all the lines that start with 'payload'. There are 2 occurrences, one for the normal image, and one for the fallback image.
Then build a target directory:
cd targets ./buildtarget gigabyte/m57sli
Finally build the image
cd gigabyte/m57sli/m57sli make
This will generate a linuxbios.rom image, which is 512KB large. That's the file that should be burned into your BIOS chip.
Make SURE that you have a fallback position: a rom chip with backup copy of your factory ROM image (you can make one with flashrom), and either a socket on the board to plug the backup chip into, or the tools and skills to remove a 'bricked' BIOS chip from the board and replace it with a socket for the backup chip.
If you do not prepare properly, you are likely to brick your motherboard. You have been warned!
You can use flashrom from the LinuxBIOS v2 tree to burn the image:
util/flashrom/flashrom -v -w linuxbios.rom
Now shut down your computer (a reset will not work, you need to power down), and restart it. Hook up a serial console so that you can see what's happening.
The mac address for the onboard network card will have changed, so you may have to modify /etc/iftab (Debian/Ubuntu, see your distro documentation for the equivalent file) to get your network working.
Did something go wrong? Use your backup rom chip (you DID make one, right?) to boot into the proprietary BIOS, and see if you can resolve the problem. Feel free to contact the friendly and helpful mailing list if you need help.
ACPI support is not implemented yet. This is a fairly major problem, and needs to be addressed soon.
There is also still an issue with I2C, which causes X startup to be very slow. You can bypass this problem by adding
to your "Device" section.
If you can help out with this, please join the mailing list and let us know!