Board:lenovo/t420

From coreboot
Revision as of 08:33, 9 December 2015 by IruCai (talk | contribs) (about the microcode, it should be an ES/QS processor issue, not IVB)
Jump to navigation Jump to search

The wiki is being retired!

Documentation is now handled by the same processes we use for code: Add something to the Documentation/ directory in the coreboot repo, and it will be rendered to https://doc.coreboot.org/. Contributions welcome!

Status

Thanks for your interest in Lenovo T420 port. The code has not been merged yet, you can see the code on gerrit and check it out.

ATTENTION: You must cherry-pick this patch before building. (It's merged to upstream, you can cherry-picked the T420 port on the upstream coreboot code.)

Issues:

  • The USB beside express card cannot funtion after S3 resume if CONFIG_USBDEBUG is set (work around: reload ehci-pci module)
  • Badly seated RAM may prevent booting (not really a problem but coreboot is more suspicious to this than vendor BIOS)

Tested:

  • Ivy Bridge processor (see below. you need to modify the config, and it needs more testing)
  • RAM module combinations of 2G+0, 4G+0, 8G+0, 0+8G, 4G+8G, 8G+8G
  • S3 (Suspend to RAM)
  • msata
  • USB
  • Video (internal)
  • Sound (integrated speakers, integrated mic, external headphones, external mic)
  • LAN
  • mini-PCIe slots (wlan)
  • bluetooth
  • Linux (through GRUB-as-payload)
  • Windows (Sandy Bridge only, through SeaBIOS using a VGA blob from X230 vendor firmware, but still do not support Ivy Bridge)
  • DVD-ROM drive
  • SD card slot
  • trackpoint
  • touchpad
  • webcam
  • Fn hotkeys (backlight control, suspend, thinklight)
  • Thinklight
  • dock (tested with a TYPE 4337)

Not Tested:

  • Video (VGA and Displayport)
  • Expresscard slot (including hotplugging)
  • mini pci-e wwan
  • Fingerprint reader.
  • Thermal management

proprietary components status

  • CPU Microcode (optional): you may need it if your system is unstable (especially you're using a ES/QS processor)
  • VGA option rom (optional): you need it if you want graphics in SeaBIOS but most payloads should work without it (text mode or corebootfb mode)
  • ME(Management Engine) => you do not have to touch it(just leave it where it is)
  • EC(Embedded Controller) => you do not have to touch it(just leave it where it is)

Flashing

T420 has an SOIC-8 flash chip of 8M. It's subdivided in roughly in 3 parts:

  • Descriptor (12K)
  • ME firmware (5M-12K)
  • System flash (3M)

ME firmware is not readable. Vendor firmware locks the flash and so you need to flash externally (unless until someone figures out a way around it).

Proceeds as follows:

  • Turn off your laptop, remove battery and AC adapter.
  • Disassemble the T420 laptop as the hardware maintenance manual says. You have to take out the mainboard, because the flash chip is under the magnesium stucture frame.
  • Connect your external SPI flasher to the SPI chip and flash it. Using an SOIC-8 clip is recommended.

When the laptop is running coreboot, you can reflash the firmware using flashrom:

 flashrom -p internal:laptop=force_I_want_a_brick -w <coreboot image>

Ivy Bridge processor support

Sandy Bridge and Ivy Bridge processor use the same socket, so an Ivy Bridge processor can be installed. Up to now only native graphics init works normally, using a VGA option ROM from an Ivy Bridge laptop (I tested it with an X230 VGA option ROM) still only supports Sandy Bridge graphics. You should use a patch on gerrit so that coreboot can use the correct code for native graphics init.

Up to now, an i7-3720QM(QS version) is tested.