The wiki is being retired!
Documentation is now handled by the same processes we use for code: Add something to the Documentation/ directory in the coreboot repo, and it will be rendered to https://doc.coreboot.org/. Contributions welcome!
Thanks for your interest in Lenovo X201 port. Issues:
- Sometimes Gnome starts to think that battery is 10 time larger than real. Information from sysfs remains correct. Doesn't appear in newer gnome
- Yellow USB port is not powered when computer is shut down or in S3.
- RAM module combinations of 4G+4G, 4G, 2G+2G,4G+2G, 2G
- suspend to RAM (S3)
- Video (both internal and VGA)
- Expresscard slot (including hotplug)
- mini-PCIe slots (both wlan and wwan)
- Linux (through GRUB-as-payload & SeaBIOS-as-payload)
- Windows (through GRUB-as-payload loading SeaBIOS image from disk; you have to use extracted VGA blob, dumped from memory isn't good enough)
- SD card slot
- Thermal management
- Fingerprint reeader.
- Digitizer on X201t variant.
proprietary components status
- CPU Microcode
- VGA option rom (optional): you need it if you wantgraphics in SeaBIOS but most payloads should work without it (text mode or corebootfb mode)
- [[Intel_Management_Engine|ME(Management Engine)] => you do not have to touch it(just leave it where it is)
- EC(Embedded Controller) => you do not have to touch it(just leave it where it is)
$ git clone https://review.coreboot.org/coreboot.git
Flash in X201 is divided roughly in 4 parts:
- Descriptor (12K)
- ME firmware (5M-12K)
- Rewriteable flash (3M-96K)
- Locked bootblock (96K)
Descriptor and bootblock are read-only. ME firmware is not readable. Rewriteable region can be rewritten easily with flashrom.
For coreboot we need to preserve descriptor and ME firmware while overwriting rewriteable region and bootblock. To achieve this there are 2 ways:
- External flasher.
- Unlock bootblock
For the first one proceeds as follows:
- Turn off your laptop, remove battery and AC adapter.
- Remove the keyboard.
- Connect your external SPI flasher to the SPI chip which is under keyboard,
around the position of trackpoint under protective layer.
I recommend using SOIC-8 clip. Depending on the flasher you use, you may have to use separate 3.3V source. Make sure not to feed more than 3.3V ot the chip. I used buspirate as flasher and 3.3V power lines from another computer. The pinout is as follows, the colors are buspirate colors
=== front (display) ==== 3.3V (red) N/C violet (CLK) MOSI (gray) | | | | dot | | | | CS (white) MISO (black) N/C ground (brown) === back (touchpad) ===
- Read the flash. Twice. Compare the files to be sure. Save a copy of it on
flashrom -p <yourprogrammer> -r flash.bin flashrom -p <yourprogrammer> -r flash2.bin diff flash.bin flash2.bin
If you have trouble reading the chip successfully, the most common problems are
- insufficient power supply
- bad contacts
- too long wires
- bad pinout
The cable shipped with buspirate was too long, and needed to be trimmed.
See also In-System Programming
- Recover descriptor and me firmare:
dd if=flash.bin of=coreboot/3rdparty/mainboard/lenovo/x201/descriptor.bin \ count=12288 bs=1M iflag=count_bytes dd if=flash.bin of=coreboot/3rdparty/mainboard/lenovo/x201/me.bin \ skip=12288 count=5230592 bs=1M iflag=count_bytes,skip_bytes
- Compile coreboot. Remember to enable HAVE_IFD and HAVE_ME_BIN
- Flash the resulting build/coreboot.rom
The other way has never been successfully used but it's known that the locking mechanism is in bootblock itself and that original firmware has a way to update it as follows:
- Flash an update of rewriteable region. On next boot bootblock parses the
image and sees that it contains a compressed copy of new bootblock. That copy is uncompressed and flashed. A way to unlock the bootblock would be to modify a firmware update to have a copy of bootblock without protection. For this you need to compress the modified block to fit into original space. The compression used is Lempel-Ziv- Huffman variant. I've written a compressor for it but unfortunately it's not performant enough.
identify the regions
[root@x201 ~]# flashrom -r bios.bin -pinternal:laptop=force_I_want_a_brick flashrom v0.9.6.1-r1563 on Linux 3.10-1-grml-amd64 (x86_64) flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... OK. Found chipset "Intel QM57". Enabling flash write... WARNING: SPI Configuration Lockdown activated. FREG0: WARNING: Flash Descriptor region (0x00000000-0x00000fff) is read-only. FREG2: WARNING: Management Engine region (0x00003000-0x004fffff) is locked. PR0: WARNING: 0x007d0000-0x01ffffff is read-only. Please send a verbose log to firstname.lastname@example.org if this board is not listed on http://flashrom.org/Supported_hardware#Supported_mainboards yet. Writes have been disabled. You can enforce write support with the ich_spi_force programmer option, but it will most likely harm your hardware! If you force flashrom you will get no support if something breaks. OK. Found Macronix flash chip "MX25L6405" (8192 kB, SPI) at physical address 0xff800000. Reading flash... FAILED.
it will print the ME regions:
FREG2: WARNING: Management Engine region (0x00003000-0x004fffff) is locked.
it will also print the chip:
Found Macronix flash chip "MX25L6405" (8192 kB, SPI) at physical address 0xff800000.
But as in this case, flashrom might misidentify the chip, this output is from this MX25L6445E
visually verify your chip's part number and find an appropriate datasheet
=>verify that its voltage matches with the programmer voltage...
- Use flashrom layouts:
-l, --layout <file>
Copy this into a file
000000000:00000fff fd 000500000:007fffff bios 000003000:004fffff me 000001000:00002fff gbe