Search results
Jump to navigation
Jump to search
- LnkCap: Port #4, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <64ns, L1 <1us LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt- ...23 KB (2,764 words) - 23:06, 21 June 2009
- on the mainboard at boot time. The payload is included in the flash rom along # Speeding up the boot ...26 KB (4,494 words) - 23:22, 18 January 2014
- ..._VGA_comments = VGA support in LinuxBIOS works fine (e.g. for displaying a boot logo), for console/X11 you need a special kernel console and Xorg driver. ...' or '''SST 39SF020A''' or '''MX 29F002NT''' PLCC32 256kiB flash memory to boot (in a socket) ...14 KB (2,140 words) - 23:21, 18 January 2014
- # After first boot, coreboot tables are in place and can be changed with the '''lxbios''' util ...we only mention '''FILO''' and '''Etherboot'''. These two will allow us to boot a Linux OS from local disk (IDE or SATA). ...18 KB (2,926 words) - 23:22, 18 January 2014
- The on-board PCMCIA and CF sockets work. coreboot can boot from CF (the stock BIOS can't). [http://www.linuxbios.org/pipermail/linuxbi on the mainboard at boot time. The payload is included in the flash rom along ...31 KB (5,497 words) - 03:50, 19 January 2014
- * CPU speed throttling * boot laptop and enjoy coreboot! ...5 KB (749 words) - 13:39, 31 December 2017
- ...for testing experimental Coreboot builds, which may or may not be able to boot properly. * Flashing speed could be improved. Now reading 1 MByte takes ~70 sec, flash & verify takes ...5 KB (793 words) - 14:22, 2 April 2013
- ...lf firmware=rtl_nic/rtl8168d-2.fw latency=0 link=no multicast=yes port=MII speed=10Mbit/s configuration: driver=hub slots=5 speed=12Mbit/s ...49 KB (5,467 words) - 01:09, 29 November 2015
- ...ensor readouts are off, and the pwm polarity seems to be inverted, but fan speed can be set. ...ote) If you install an AMD AM3/AM2+ CPU on AM2 motherboard, the system bus speed will downgrade from HT3.0(5200 MT/s) to HT1.0 (2000 MT/s); however, the fre ...31 KB (4,898 words) - 08:37, 30 August 2017
- Boot the legacy BIOS, and use [[VGA_support]] chapter .... But read [[SeaBIOS]] for how to add payloads to SeaBIOS and set SeaBIOS' boot order to run your payload. ...9 KB (1,445 words) - 12:10, 2 May 2017
- LnkCap: Port #3, Speed 2.5GT/s, Width x2, ASPM L0s, Latency L0 <512ns, L1 <4us LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- ...64 KB (8,594 words) - 19:43, 5 October 2008
- Boot from CD is supported Selectable boot is supported ...58 KB (8,251 words) - 19:49, 5 October 2008
- ..._VGA_comments = VGA support in LinuxBIOS works fine (e.g. for displaying a boot logo), for console/X11 you need a special kernel console and Xorg driver. * '''Pm29F002T''' DIL32 256kiB Flash memory to boot ...10 KB (1,462 words) - 23:21, 18 January 2014
- LnkCap: Port #1, Speed 5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <512ns, L1 <64us LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt- ...92 KB (9,722 words) - 02:31, 29 November 2015
- ...b|right|ASUS KGPE-D16 on the development stand at Raptor Engineering.<p>To boot with a second CPU package installed, the 2nd EPS12V connector MUST be conne .... Failing to clear the CMOS will typically result in odd hangs during the boot process. ...19 KB (3,122 words) - 16:54, 10 May 2018
- ...Mbit) flash part and a DoC flash part. This is an ideal situation. We can boot a fairly complex LinuxBIOS from the FLASH part, as it is at least 8 times l ...it hard to get it all right. Actual SDRAM parameters such as CAS latency, speed, etc. are maintained on a Serial EEPROM (SEEPROM) on the SDRAM module. The ...12 KB (2,131 words) - 17:36, 16 November 2008
- ...station: Bonn Hbf) is reachable by high-speed train (ICE), and other high-speed train stations (Cologne, Siegburg) are reasonably close (30 minutes). http: ...ivial drivers for storage, filesystems, network, etc. which may be used to boot the machine. ...17 KB (2,573 words) - 15:18, 11 May 2017
- the speed to 115200 Bps None, 8, 1 and boot up the IP530. ...of a distro that uses the serial console for its installation. The kernel boot customation, must be something like this "apci=off console=ttyS0,115200n8" ...16 KB (2,587 words) - 23:22, 18 January 2014
- |SATA_comments = SATA mode (IDE/AHCI) and speed (3Gbps/6Gbps) can be changed through an NVRAM setting ...keyboards. When using SeaBIOS, the keyboard might not be detected on every boot (likely some timing issue). Tianocore can only initialize the keyboard if i ...63 KB (8,660 words) - 16:06, 10 May 2018