VGA support: Difference between revisions

From coreboot
Jump to navigation Jump to search
(Add some instructions specific to the Via CN700 (epia-CN))
No edit summary
 
(34 intermediate revisions by 13 users not shown)
Line 1: Line 1:
== VGA initialization in coreboot v2 ==
== VGA initialization in coreboot ==


=== General ===
Since coreboot v4 you can configure VGA initialization in Kconfig. For older versions of coreboot check the history of this page.


You need to enable two CONFIG options in your Mainboard Option.lb
First do:


<source lang="bash">
<source lang="bash">
# VGA Console
$ make menuconfig
option CONFIG_CONSOLE_VGA=1
option CONFIG_PCI_ROM_RUN=1
</source>
</source>


'''CONFIG_PCI_ROM_RUN''' will use the embedded x86 emulator to run the BIOS image in the expansion ROM of a PCI device.
Then go
'''CONFIG_CONSOLE_VGA''' will redirect console messages to the VGA screen once VGA card is initialized.
    Chipset  --->
      [*] Setup bridges on path to VGA adapter
      [*] Run VGA option ROMs
      Option ROM execution type (Native mode)  --->


For add-on (PCI/PCIe/PCI-X/AGP) VGA cards, you don't have to do anything else besides these two CONFIG options.
Alternatively you can choose the "Secure mode" to run the VGA option rom in a contained environment.
If your mainboard has an on-board VGA chip and you insert another VGA add-on card, the add-on
 
VGA card will be used instead of the on-board VGA chip.
If you have no on-board graphics, you are done configuring coreboot at this point. You may exit configuration, and run make to get your VGA enabled coreboot image.


=== On-board Video Devices ===
=== On-board Video Devices ===


If you want to use the onboard VGA chip, you have to add the following options in addition to the CONFIG options described above.
If you run coreboot on a system with on-board graphics, you have to embed a VGA  on the top level, enter the file name of your option rom and the PCI ID of the associated graphics device in the form <vendor_id>,<device_id>:


==== Mainboard Configuration ====
    VGA BIOS  --->
'''Note:''' This step is not necessary for the VIA CN700 chipset.
    [*] Add a VGA BIOS image
    (oprom-0.rom) VGA BIOS path and filename
    (8086,27a2) VGA device PCI IDs


1. In the mainboard's Config.lb (./src/mainboard/<mfg>/<board>/Config.lb) You need to specify the device number for your on-board VGA and the address that the video bios will show up at in the system.
That's it, exit configuration, and run make to get your VGA enabled coreboot image.


<source lang = bash>
== How to retrieve a good video bios ==
device pci 9.0 on  # PCI
        chip drivers/pci/onboard
                device pci 9.0 on end
                register "rom_address" = "0xfff80000" #512k image
                #register "rom_address" = "0xfff00000" #1M image
        end
end
</source>


Replace the 9.0 with the dev.fn of your vga device.  You can find this number by doing a 'lspci' from the board booted under linux.
There are various ways to get hold of the video bios blob and not all work equally good for all boards (rather the opposite).
Please make sure the device number is correct. Otherwise the config code can not compute the proper ROM address.


The best way is to extract it from the vendor firmware.
In the case of a traditional x86 BIOS this is rather easy and very reliable.
On UEFI systems there does not seem to be a unified way of success but sometimes the steps below work.


===== How to compute the "rom_address" value =====
Another category is downloading the blobs directly.
Some vendors offer them in graphics driver packages etc. and you might even find them on enthusiasts website dedicated to firmware modding etc.


ROM (called 'flash' a lot) chips are located directly below 4Gbyte  (0xffffffff) boundary.
The most delicate ways are by dumping the blob from a running system.
This might sound like the most reasonable way but the image present after boot might not be the same as it is (to be) stored in flash (e.g. if it is self modifying).
However, in some cases this is the only way and then it is quite comfortable.


So you need to calculate the address by subtracting the
=== RECOMMENDED: Extracting from your vendor bios image ===
flash chip size (and adding the offset within the image)


In coreboot the offset within the image is 0, because its the first
The recommended method is to take your mainboard vendor's BIOS image (if there is one) and extract the VGA BIOS using a tool called [[bios_extract]].
thing in the coreboot image.


So you need to compute the address in the systems memory space where the start of the video bios will show up.
$ git clone http://review.coreboot.org/p/bios_extract.git


To do this you take the 4Gb of address and subtract the size of your coreboot image.
This is the most reliable way:
0x100000000 - (ROM size in Kb * 1024)
* You are guaranteed to get an image that fits to your onboard VGA
* Even if your VGA BIOS uses self-modifying code you get a correct image


You can do this in bash by:
Decompress your rom image with:
$ ./bios_extract hdmag217.rom


<source lang="bash">
If bios_decode fails with a message like
biossize=256
Using file "hdmag217.rom" (513kB)
printf "0x%x\n" $(( 0x100000000 - ($biossize*1024) ))
Found Phoenix BIOS "Phoenix ServerBIOS 3 Release 6.0    "
</source>
Version "DEVEL4E0", created on 03/20/06 at 14:37:39.
Error: Invalid module signature at 0x80581


Addresses for popular chip sizes:
then you have to cut the flash chip description off the image. In this case the BIOS image is 512KB, so you do
  256K 0xfffc0000
  $ dd if=hdmag217.rom of=hdma.rom bs=512k count=1
  512k  0xfff80000
  1+0 records in
  1024k 0xfff00000
  1+0 records out
  524288 bytes transferred in 0.000883 secs (593688784 bytes/sec)




==== Target Configuration ====
You will get an output similar to this:


2. You still need to modify your target 'Config.lb' to reserve space for the additional video biosReduce the size of your coreboot image by the size of the video bios. You will prepend the video bios to the coreboot image in step 3.
Using file "hdma.rom" (512kB)
Found Phoenix BIOS "Phoenix ServerBIOS 3 Release 6.0    "
Version "DEVEL4E0", created on 03/20/06 at 14:37:39.
0x715FC ( 27134 bytes)  ->  romexec_0.rom
0x6E1CB ( 13338 bytes)  ->  strings_0.rom (29401 bytes)
0x6D65D (  2899 bytes)  ->  display_0.rom (4128 bytes)
0x6B62E (  8208 bytes)  ->  update_0.rom
0x6B1E3 (  1072 bytes)  ->  decompcode_0.rom [0x5000:0xB6D0]
0x6564F ( 23421 bytes)  ->  oprom_0.rom (36864 bytes)
0x65608 (    44 bytes)  ->  tcpa_H_0.rom (32 bytes)
0x65592 (    91 bytes)  ->  acpi_1.rom (116 bytes)
0x65519 (    94 bytes)  ->  acpi_2.rom (244 bytes)
0x654ED (    13 bytes)  ->  tcpa_*_0.rom
0x64D4F (  1927 bytes)  ->  bioscode_0.rom (31382 bytes) [0xF000:0x856A]
0x60020 ( 19728 bytes)  ->  romexec_1.rom
0x570D9 ( 36656 bytes)  ->  oprom_1.rom (61440 bytes)
0x4DB9D ( 38177 bytes)  ->  oprom_2.rom (63488 bytes)
  0x46493 ( 30447 bytes)  ->  oprom_3.rom (65536 bytes)
0x41DAB ( 18125 bytes)  ->  logo_0.rom (310162 bytes)
0x39CA5 ( 25439 bytes)  ->  oprom_4.rom (51200 bytes)
0x36005 ( 15493 bytes)  ->  setup_0.rom (37682 bytes)
0x325D7 ( 14867 bytes)  ->  template_0.rom (37728 bytes)
0x2FA36 ( 11142 bytes)  ->  miser_0.rom (16208 bytes)
0x2E63C (  5087 bytes)  ->  tcpa_Q_0.rom (16096 bytes)
0x2D7C3 (  3678 bytes)  ->  acpi_0.rom (10464 bytes)
0x1FA2A ( 41023 bytes)  ->  bioscode_1.rom (56080 bytes) [0xE000:0x40F0]
0x14FE0 ( 43567 bytes)  ->  bioscode_2.rom (62416 bytes) [0x6000:0xCC30]
0x0EB4C ( 25721 bytes)  ->  bioscode_3.rom (36976 bytes) [0x6000:0x3BC0]
0x0D0A0 (  6801 bytes)  ->  bioscode_4.rom (31856 bytes) [0x5000:0xBF50]


in the normal section
Now you can check the option roms (oprom_?.rom) with the tool romheaders which is part of the [http://www.openfirmware.info/FCODE_suite FCode Suite] (in debian-based distros, you can get it by installing the '''fcode-utils''' package):


<source lang="bash">
$ romheaders oprom_0.rom
romimage "normal"
   # 48K for SCSI FW or ATI ROM
Image 1:
   option ROM_SIZE = 475136
PCI Expansion ROM Header:
</source>
  Signature: 0x55aa (Ok)
  CPU unique data: 0x48 0xeb 0x7b 0x01 0x76 0x00 0x00 0x00
                    0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
  Pointer to PCI Data Structure: 0x017c
PCI Data Structure:
  Signature: 0x50434952 'PCIR' (Ok)
  Vendor ID: 0x1002
   Device ID: 0x4752
  Vital Product Data:  0x0000
  PCI Data Structure Length: 0x0018 (24 bytes)
  PCI Data Structure Revision: 0x00
  Class Code: 0x030000 (VGA Display controller)
  Image Length: 0x0048 blocks (36864 bytes)
  Revision Level of Code/Data: 0x0421
  Code Type: 0x00 (Intel x86)
  Last-Image Flag: 0x80 (last image in rom)
  Reserved: 0x0000
Platform specific data for x86 compliant option rom:
   Initialization Size: 0x48 (36864 bytes)
  Entry point for INIT function: 0x80


or if you only have a "fallback" boot then use the "fallback" section instead.
Congratulations, that's your option rom (compare PCI IDs and Class Code to find it among the option roms).


In the above example the bios chip is 512Kb part.  The video bios is  48Kb.  So (512*1024)-(48*1024) = 475136.
=== UEFI Method ===


'''Note:''' The Via CN700 chipset also requires legacy BIOS support. This can be found or at http://bochs.sourceforge.net/ or in the Debian package bochsbios, filename /usr/share/bochs/BIOS-bochs-legacy.  You'll need to leave an additional 64k of space for the Bochs BIOS.
UEFI's format is more structured than that of a traditional flat binary BIOS. In order to extract the VBIOS Option ROM you will need
to parse out the UEFI Volumes and sub-Volumes out the UEFI filesystem using the [https://github.com/LongSoft/UEFITool UEFITool].


==== Creating an Image ====
* Look for the " CSMCORE " DXE Driver ? usually having the hash 'a062cf1f-8473-4aa3-8793-600bc4ffe9a8'?
* Search for text "VGA Compatible BIOS" ('''uncheck unicode''')
* Search for text "PCIR" ('''uncheck unicode''')


3. Finally, prepend your video bios to the coreboot.rom
Double clicking the matching line in the "Messages" section should select the appropriate RAW section. From the menu select "Action -> Section -> Extract Body...".


<source lang="bash">
=== Downloading ===
cat videobios.bin coreboot.rom > final_coreboot.rom
</source>


where ''videobios.bin'' is the name of your video bios image.
There are sites that have video BIOS ROMs on their website (with all implications of retrieving a binary from an unknown source and executing it...).
You need to make sure the final_coreboot.rom size is the size of your ROM chip. Normally 256kb, 512kb, or 1024Kb.


See below for instructions on how to retrieve the video BIOS from your factory ROM.
For Intel onboard graphics you can download the vbios (vga bios) from Intel's download section. The vbios is included with some versions of the graphics driver. The summary will say something like "NOTE:These materials are intended for use by developers.Includes VBIOS". The actual vbios file is the *.dat file included with the graphics driver.


'''For Via CN700:'''
=== Retrieval via Linux kernel ===
<source lang="bash">
Some Linux drivers (e.g. <tt>radeon</tt> for AMD) make option ROMs like the video blob available to user space via sysfs.
cat videobios.bin bochsbios.bin coreboot.rom > final_coreboot.rom
To use that to get the blob you need to enable it first.
</source>
To that end you need to determine the path within <tt>/sys</tt> corresponding to your graphics chip.
 
It looks like this: <tt>/sys/devices/pci<domain>:<bus>/<domain>:<bus>:<slot>.<function>/rom</tt>.
== VGA initialization in coreboot v3 ==
 
In coreboot v3 you have to set your PCI option ROM execution method under the '''Device''' menu. The default is x86emu. To get a smaller (and slightly more insecure) version, you can switch to vm86. If you don't want option rom execution, set it to Disabled.


=== On-board devices ===
You can get the respective information with <tt>lspci</tt>, for example:
# lspci -tv
-[0000:00]-+-00.0  Advanced Micro Devices, Inc. [AMD] Family 16h Processor Root Complex
            +-01.0  Advanced Micro Devices, Inc. [AMD/ATI] Kabini [Radeon HD 8210]
...


To add option roms for on-board video cards to your coreboot image, you can just add the image using lar:
Here the the needed bits (for the ROM of the Kabini device) are:
* PCI domain: (almost always) 0000
* PCI bus: (also very commonly) 00
* PCI slot: 01 (logical slot; different from any physical slots)
* PCI function: 0 (a PCI device might have multiple functions... shouldn't matter here)


<source lang="bash">
To enable reading of the ROM you need to write 1 to the respective file, e.g.:
lar -C lzma -a coreboot.rom vgabios.rom:pciXXXX,YYYY.rom
</source>


In the above example, vgabios.rom is the name of your option rom on disk. XXXX is the PCI vendor ID of your on-board video adapter and YYYY is its PCI device ID.
echo 1 > /sys/devices/pci0000:00/0000:00:01.0/rom


== How to retrieve a good video bios ==
The same file should then contain the video blob and it should be possible to simply copy it, e.g.:


=== Extracting from your vendor bios image ===
cp /sys/devices/pci0000:00/0000:00:01.0/rom vgabios.bin


The recommended method is to take your mainboard vendor's BIOS image and extract the VGA BIOS using a tool called awardeco/amideco/phnxdeco. This is the most reliable way:
<tt>romheaders</tt> should print reasonable output for this file.
* You are guaranteed to get an image that fits to your onboard VGA
* Even if your VGA BIOS uses self-modifying code you get a correct image
With this method, you may need to pad the image to a certain size, e.g. 64k.  This is necessary at least for VIA CN700 chipsets where the factory VGA bios is smaller.


=== Downloading ===
Intel Graphics supports this method. See [https://01.org/linuxgraphics/documentation/development/how-dump-video-bios How to dump Video BIOS].


There are sites that have video bios roms on their website. (I know of this one for nvidia cards: [http://whitebunny.demon.nl/hardware/chipset_nvidia.html])
=== Extraction from mapped memory (if everything else fails) ===


=== Extracting from the system ===
However you might be able to retrieve your on-board video BIOS with Linux as well.


However you should be able to retrieve your own video bios as well with linux.
* Boot up a machine with a commercial BIOS (not coreboot) with the video card you wish to work under coreboot.
* Boot up a machine with a commercial bios (not coreboot) with the video card you wish to work under coreboot.
* You can see where and how much your card's bios is using by doing a  
* You can see where and how much your card's bios is using by doing a  
<source lang="bash">cat /proc/iomem | grep 'Video ROM'</source>
<source lang="bash">grep 'Video ROM' /proc/iomem</source>
* From the command line enter:<br /><source lang="bash">dd if=/dev/mem of=vgabios.bin bs=1k count=64 skip=768</source> This assumes you card's bios is cached at 0xc0000, and is 64K long.
* From the command line enter:<br /><source lang="bash">dd if=/dev/mem of=vgabios.bin bs=1k count=64 skip=768</source> This assumes you card's BIOS is cached at 0xc0000, and is 64K long.
<br /><source lang="bash">dd if=/dev/mem of=video.bios.bin.4 bs=65536 count=1 skip=12</source>
<br /><source lang="bash">dd if=/dev/mem of=video.bios.bin.4 bs=65536 count=1 skip=12</source>
This works for many of the VIA Epia boards.<br>
This works for many of the VIA Epia boards.<br>
Alternatively you can automatically generate it using this nice script from Peter Stuge:<br />
Alternatively you can automatically generate it using this nice script from Peter Stuge:<br />
<source lang="bash">
<source lang="bash">
$ cat /proc/iomem | grep 'Video ROM' | (read m; m=${m/ :*}; s=${m/-*}; e=${m/*-}; \
cat /proc/iomem | grep 'Video ROM' | (read m; m=${m/ :*}; s=${m/-*}; e=${m/*-}; \
$ dd if=/dev/mem of=vgabios.bin bs=1c skip=$[0x$s] count=$[$[0x$e]-$[0x$s]+1])
dd if=/dev/mem of=vgabios.bin bs=1c skip=$[0x$s] count=$[$[0x$e]-$[0x$s]+1])
</source>
</source>
* You now have a video bios image
* You (might) have a video BIOS image now. Check it at least with romheaders (as described above).
 
== YABEL ==
* Yabel can be used to trace the VGA option rom.
* However its ability to prevent the option rom to do nasty things is limited: Often the GPU offers a way (e.g. trough an IO BAR) to access arbitrary locations in RAM, so limiting access of the GPU's PCI device to the option rom wouldn't contain it completely.
 
See [[Coreboot Options]] for more information about the option.
 
[[Category:Blobs]]

Latest revision as of 14:47, 12 April 2016

VGA initialization in coreboot

Since coreboot v4 you can configure VGA initialization in Kconfig. For older versions of coreboot check the history of this page.

First do:

<source lang="bash">

$ make menuconfig

</source>

Then go

    Chipset  --->
     [*] Setup bridges on path to VGA adapter 
     [*] Run VGA option ROMs
     Option ROM execution type (Native mode)  --->

Alternatively you can choose the "Secure mode" to run the VGA option rom in a contained environment.

If you have no on-board graphics, you are done configuring coreboot at this point. You may exit configuration, and run make to get your VGA enabled coreboot image.

On-board Video Devices

If you run coreboot on a system with on-board graphics, you have to embed a VGA on the top level, enter the file name of your option rom and the PCI ID of the associated graphics device in the form <vendor_id>,<device_id>:

   VGA BIOS  --->
    [*] Add a VGA BIOS image
    (oprom-0.rom) VGA BIOS path and filename
    (8086,27a2) VGA device PCI IDs

That's it, exit configuration, and run make to get your VGA enabled coreboot image.

How to retrieve a good video bios

There are various ways to get hold of the video bios blob and not all work equally good for all boards (rather the opposite).

The best way is to extract it from the vendor firmware. In the case of a traditional x86 BIOS this is rather easy and very reliable. On UEFI systems there does not seem to be a unified way of success but sometimes the steps below work.

Another category is downloading the blobs directly. Some vendors offer them in graphics driver packages etc. and you might even find them on enthusiasts website dedicated to firmware modding etc.

The most delicate ways are by dumping the blob from a running system. This might sound like the most reasonable way but the image present after boot might not be the same as it is (to be) stored in flash (e.g. if it is self modifying). However, in some cases this is the only way and then it is quite comfortable.

RECOMMENDED: Extracting from your vendor bios image

The recommended method is to take your mainboard vendor's BIOS image (if there is one) and extract the VGA BIOS using a tool called bios_extract.

$ git clone http://review.coreboot.org/p/bios_extract.git

This is the most reliable way:

  • You are guaranteed to get an image that fits to your onboard VGA
  • Even if your VGA BIOS uses self-modifying code you get a correct image

Decompress your rom image with:

$ ./bios_extract hdmag217.rom

If bios_decode fails with a message like

Using file "hdmag217.rom" (513kB)
Found Phoenix BIOS "Phoenix ServerBIOS 3 Release 6.0     "
Version "DEVEL4E0", created on 03/20/06 at 14:37:39.
Error: Invalid module signature at 0x80581

then you have to cut the flash chip description off the image. In this case the BIOS image is 512KB, so you do

$ dd if=hdmag217.rom of=hdma.rom bs=512k count=1
1+0 records in
1+0 records out
524288 bytes transferred in 0.000883 secs (593688784 bytes/sec)


You will get an output similar to this:

Using file "hdma.rom" (512kB)
Found Phoenix BIOS "Phoenix ServerBIOS 3 Release 6.0     "
Version "DEVEL4E0", created on 03/20/06 at 14:37:39.
0x715FC ( 27134 bytes)   ->   romexec_0.rom
0x6E1CB ( 13338 bytes)   ->   strings_0.rom	(29401 bytes)
0x6D65D (  2899 bytes)   ->   display_0.rom	(4128 bytes)
0x6B62E (  8208 bytes)   ->   update_0.rom
0x6B1E3 (  1072 bytes)   ->   decompcode_0.rom			 [0x5000:0xB6D0]
0x6564F ( 23421 bytes)   ->   oprom_0.rom	(36864 bytes)
0x65608 (    44 bytes)   ->   tcpa_H_0.rom	(32 bytes)
0x65592 (    91 bytes)   ->   acpi_1.rom	(116 bytes)
0x65519 (    94 bytes)   ->   acpi_2.rom	(244 bytes)
0x654ED (    13 bytes)   ->   tcpa_*_0.rom
0x64D4F (  1927 bytes)   ->   bioscode_0.rom	(31382 bytes)	 [0xF000:0x856A]
0x60020 ( 19728 bytes)   ->   romexec_1.rom
0x570D9 ( 36656 bytes)   ->   oprom_1.rom	(61440 bytes)
0x4DB9D ( 38177 bytes)   ->   oprom_2.rom	(63488 bytes)
0x46493 ( 30447 bytes)   ->   oprom_3.rom	(65536 bytes)
0x41DAB ( 18125 bytes)   ->   logo_0.rom	(310162 bytes)
0x39CA5 ( 25439 bytes)   ->   oprom_4.rom	(51200 bytes)
0x36005 ( 15493 bytes)   ->   setup_0.rom	(37682 bytes)
0x325D7 ( 14867 bytes)   ->   template_0.rom	(37728 bytes)
0x2FA36 ( 11142 bytes)   ->   miser_0.rom	(16208 bytes)
0x2E63C (  5087 bytes)   ->   tcpa_Q_0.rom	(16096 bytes)
0x2D7C3 (  3678 bytes)   ->   acpi_0.rom	(10464 bytes)
0x1FA2A ( 41023 bytes)   ->   bioscode_1.rom	(56080 bytes)	 [0xE000:0x40F0]
0x14FE0 ( 43567 bytes)   ->   bioscode_2.rom	(62416 bytes)	 [0x6000:0xCC30]
0x0EB4C ( 25721 bytes)   ->   bioscode_3.rom	(36976 bytes)	 [0x6000:0x3BC0]
0x0D0A0 (  6801 bytes)   ->   bioscode_4.rom	(31856 bytes)	 [0x5000:0xBF50]

Now you can check the option roms (oprom_?.rom) with the tool romheaders which is part of the FCode Suite (in debian-based distros, you can get it by installing the fcode-utils package):

$ romheaders oprom_0.rom 

Image 1:
PCI Expansion ROM Header:
  Signature: 0x55aa (Ok)
  CPU unique data: 0x48 0xeb 0x7b 0x01 0x76 0x00 0x00 0x00
                   0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
  Pointer to PCI Data Structure: 0x017c

PCI Data Structure:
  Signature: 0x50434952 'PCIR' (Ok)
  Vendor ID: 0x1002
  Device ID: 0x4752
  Vital Product Data:  0x0000
  PCI Data Structure Length: 0x0018 (24 bytes)
  PCI Data Structure Revision: 0x00
  Class Code: 0x030000 (VGA Display controller)
  Image Length: 0x0048 blocks (36864 bytes)
  Revision Level of Code/Data: 0x0421
  Code Type: 0x00 (Intel x86)
  Last-Image Flag: 0x80 (last image in rom)
  Reserved: 0x0000

Platform specific data for x86 compliant option rom:
  Initialization Size: 0x48 (36864 bytes)
  Entry point for INIT function: 0x80

Congratulations, that's your option rom (compare PCI IDs and Class Code to find it among the option roms).

UEFI Method

UEFI's format is more structured than that of a traditional flat binary BIOS. In order to extract the VBIOS Option ROM you will need to parse out the UEFI Volumes and sub-Volumes out the UEFI filesystem using the UEFITool.

  • Look for the " CSMCORE " DXE Driver ? usually having the hash 'a062cf1f-8473-4aa3-8793-600bc4ffe9a8'?
  • Search for text "VGA Compatible BIOS" (uncheck unicode)
  • Search for text "PCIR" (uncheck unicode)

Double clicking the matching line in the "Messages" section should select the appropriate RAW section. From the menu select "Action -> Section -> Extract Body...".

Downloading

There are sites that have video BIOS ROMs on their website (with all implications of retrieving a binary from an unknown source and executing it...).

For Intel onboard graphics you can download the vbios (vga bios) from Intel's download section. The vbios is included with some versions of the graphics driver. The summary will say something like "NOTE:These materials are intended for use by developers.Includes VBIOS". The actual vbios file is the *.dat file included with the graphics driver.

Retrieval via Linux kernel

Some Linux drivers (e.g. radeon for AMD) make option ROMs like the video blob available to user space via sysfs. To use that to get the blob you need to enable it first. To that end you need to determine the path within /sys corresponding to your graphics chip. It looks like this: /sys/devices/pci<domain>:<bus>/<domain>:<bus>:<slot>.<function>/rom.

You can get the respective information with lspci, for example:

# lspci -tv
-[0000:00]-+-00.0  Advanced Micro Devices, Inc. [AMD] Family 16h Processor Root Complex
           +-01.0  Advanced Micro Devices, Inc. [AMD/ATI] Kabini [Radeon HD 8210]
...

Here the the needed bits (for the ROM of the Kabini device) are:

  • PCI domain: (almost always) 0000
  • PCI bus: (also very commonly) 00
  • PCI slot: 01 (logical slot; different from any physical slots)
  • PCI function: 0 (a PCI device might have multiple functions... shouldn't matter here)

To enable reading of the ROM you need to write 1 to the respective file, e.g.:

echo 1 > /sys/devices/pci0000:00/0000:00:01.0/rom

The same file should then contain the video blob and it should be possible to simply copy it, e.g.:

cp /sys/devices/pci0000:00/0000:00:01.0/rom vgabios.bin

romheaders should print reasonable output for this file.

Intel Graphics supports this method. See How to dump Video BIOS.

Extraction from mapped memory (if everything else fails)

However you might be able to retrieve your on-board video BIOS with Linux as well.

  • Boot up a machine with a commercial BIOS (not coreboot) with the video card you wish to work under coreboot.
  • You can see where and how much your card's bios is using by doing a

<source lang="bash">grep 'Video ROM' /proc/iomem</source>

  • From the command line enter:
    <source lang="bash">dd if=/dev/mem of=vgabios.bin bs=1k count=64 skip=768</source> This assumes you card's BIOS is cached at 0xc0000, and is 64K long.


<source lang="bash">dd if=/dev/mem of=video.bios.bin.4 bs=65536 count=1 skip=12</source> This works for many of the VIA Epia boards.
Alternatively you can automatically generate it using this nice script from Peter Stuge:
<source lang="bash"> cat /proc/iomem | grep 'Video ROM' | (read m; m=${m/ :*}; s=${m/-*}; e=${m/*-}; \ dd if=/dev/mem of=vgabios.bin bs=1c skip=$[0x$s] count=$[$[0x$e]-$[0x$s]+1]) </source>

  • You (might) have a video BIOS image now. Check it at least with romheaders (as described above).

YABEL

  • Yabel can be used to trace the VGA option rom.
  • However its ability to prevent the option rom to do nasty things is limited: Often the GPU offers a way (e.g. trough an IO BAR) to access arbitrary locations in RAM, so limiting access of the GPU's PCI device to the option rom wouldn't contain it completely.

See Coreboot Options for more information about the option.